Good to know about wallpaper. Here you will get tips and make it yourself a description of how to set up wallpaper and prepare for wallpaper.

All about wallpaper and pre-work before wallpaper

All about wallpaper and pre-work before wallpaper


In this article you will learn more about wallpapering with detailed information and make it yourself instructions on setting up wallpaper and prepares you before you're going to tap.

It will be noticeable if you have tampered with the preliminary work on a wallpaper. If you get rid of dirty and dirty walls before setting up new wallpaper, you can not expect the wallpaper stick to fit properly. As a result, the wallpaper bubbles. It can even loosen from the wall after some time. Examine the walls carefully so that you can calculate approximately how long the entire work takes. If it is a widely used room to be freshened up, it may be important for the rest of the family to know how long the room is "occupied."

If the wall is so damaged that you have to do extensive flushing and grinding work, you must even count on the time it takes for the fluff to dry when planning the rest of the wallpaper. Should you put a light wallpaper on a dark surface, you should first paint the surface with primer. The paint must then dry for at least one day before continuing the wallpaper. No matter what condition the walls are, start by removing all nails, hooks and screws from the walls. Once you've done that, you probably discover one or more holes that should be spilled again. Before shredding flaked surfaces, you should protect furniture and floors, otherwise you will have a slip dust everywhere. In an older house it is common for several layers of wallpaper to be placed on each other. Then it may be a good idea to tear down all the wallpaper and start from the beginning.

It may be time consuming to get rid of old wallpaper, but there are aids. First of all, you should have a good scratch, for example, a broad packet works excellent. Secondly, there are wallpaper-solving means that you can "wet" the wallpaper with, so it loosens more easily. If the wallpaper is hard, you have another possibility of a hot air gun. Once done, review the surfaces again. Light from the side of the wall with a flashlight, so you discover any misses easier. A small and almost invisible unevenness can be enhanced when the wallpaper is in place. If you are unlucky, the light drops on the small insert or the bulge and then it is clearly visible.

Tools:

Hammers with claw (1) Cutting blade (2) Screwdriver (3) Knife blade knife (4) Steel patch (4) 5) Sprayer (12) Protective gloves (13)
Material:

Release paper, Wallpaper paste, Wallpaper dissolving agent, Spackle , Basic Color, Paintsoda, Fiberglass Strips.
Worth knowing when to wallpaper

Most of the wallpaper is now plastic coated. To remove such wallpaper by means of wallpaper-solving agents, first pull off the surface layer. Otherwise, the means will not work properly. You can not tear loose loose tabs from plastic wallpaper. Instead, cut the tape piece with a sharp knife and flap the roughness to get a smooth and fine wallpaper.

Selecting wallpaper before wallpaper

The funniest part of the preamble before wallpaper is no doubt when it's time to choose the wallpaper. Before going to the store, you should know what requirements you put on the new wallpaper. Should the wallpaper sit in a children's room, or maybe you want it to be easy to wash off? Then choose among the vinyl tapes. However, the wallpaper should be in a room where you have planned to decorate the walls with paintings, so you should not choose from wallpaper with overly dominant patterns.

It may seem a bit ridiculous to remind you to know what environment you are going to have the wallpaper But because there is such a large selection of wallpapers, it greatly facilitates if you have thought about your requirements and wishes once and twice.

Another task you should bring to the store is how much space you are going to tap. With the help of the measures you get help calculating how many rolls are available and what it costs. You can easily figure out how many rolls you need.

A wallpaper roll is usually 10 meters long and 53 inches wide. If the space is square, multiply the width of one wall by 4. If the space is rectangular, you must add the short side to the long side and multiply the number of wall meters by 2. In both cases you will know the circumference of the room. You can gain access by multiplying the perimeter of the ceilings and multiplying the sum by 2.

Remove nail

1.Add a piece of wood between the wall and the hammer when pulling nails, hooks and screws.


2.Close off main switch. Then unscrew the covers to all switches and connectors.


Old wallpaper as substrate

1.Remove wallpaper residues around windows and doors, by hand or with a flap. Be careful not to damage the wood.


2.Remove the wallpaper around door lining and window frames. Also cut the wallpaper in all corners. This to get sharp corners.


3.Read loosely loose wallpaper. When you run, you get so thin edges that they are often easy to "troll away" with slippers.


4.Remove the floorboards. Note in which order you unload them, so it is easier to reassemble them.


5.Remove all irregularities in the surface. If you are going to wallpaper on top of an old wallpaper, drop all wallpaper shards.


6.Place the surface with water - and let the wallpaper suck. This is to check how good the old wallpaper is on the wall.


7.Bubbles the wallpaper only in a few places, you can either punch and tear off the wallpaper in these places.


8.You may make the wallpaper.


9.Bubbles the whole wallpaper itself, there is no idea to fix it. Tear down the wallpaper to get a better wallpaper.


10.When you take down a wallpaper that sticks well to the substrate, use wallpaper-solving agents. Spray the liquid with a sponge.


11.Let the wallpaper to absorb the liquid. After a while, the wallpaper will loosen. Use a wide-flap and scrape the wallpaper.


12.Warm Air Gun.


Tips

If you also want to paint the ceiling, you should do it before the wallpaper. You may risk splashing on the newly painted wall. It's easy to mix to your own soda solution to wash the walls. Take some soda to ten parts cold water. Wear protective gloves when working with soda, otherwise you may have skin irritations. Before starting wallpaper it is important to remove all the screws, nails and hooks out of the wall.

Warning

If you need to do extensive grinding work, always use a so-called dust filter mask.

Surfaces that can break through

1.Pack the entire surface if you are wallpapering over a texture or weave with a waterproof flap.


2. When flushed has dried the surface evenly. Can you feel the texture of the hand, flush and grind again.


3.If the wallpaper surface is dark or patterned, ground the surface with alkyd paint. Let the paint dry for at least 1 day.


4.Pack the old wet room patch with wet-strength patch.


Painted surfaces

1. Before painting a painted surface or a wet room drain, wash the dirt with a target wash. Use gloves.


2.Wash the wall carefully with water repeatedly. There must be no target cleaning left on the wall.


Make cracks and holes

1.Replace the cracks in the wall with a triangle scraper. Scrape the bottom of a flat surface or else do not stick.


2.If the crack is large you can use fiberglass strips. Fixed with woven adhesive. When the glue is dirt flushed with sandpackle.


3.If the plaster or paint has flagnat, scrape all loose paint / putty. It is important that you scrape away all loose layers.


4.Pack again damage with sandpackel. Larger areas are packed wide. Deep cavities are spilled twice.


5.Use a steel stack and flip back all minor damage to the wall. Let the drip wipe properly.


6.Sleep a not too coarse sandpaper. The filler surfaces should feel even and level with the wall.


New wall of building board

1.Use the hammer and fit all nail heads firmly into the substrate. Flip over all nails.


2.Use sand dirt and flip back all nail holes. Make sure you do not miss a hole.


3.Pack all joints between the building plates. Begin at the bottom of each joint and flush upwards. Flush smoothly and evenly.


4.Lip all fluffy surfaces with a fine release paper. You should go by hand. Use a slip clamp so the work is a little easier.


5.Pack glass fiber strips over the joints. Construction plates "move" and the strips prevent the splash from cracking.


Tips


When grinding the walls, always close all doors to the other house. If you have an open floor plan in the house, it can be difficult to prevent the grinding dust from spreading. Hang wet sheets in the passages, so the dust will dampen significantly. When flushing deeper cavities, you can mix some plaster into the flask. Then there is less risk of flaking.



Video: How To Hang Pre-pasted Wallpaper for Beginners (paper by Bouclair Home - DIY|

Share

Comments