Filler and filler is a good and often necessary reason for most renovation work. It is used to get flat surfaces to add a beautiful surface layer, such as paint, wallpaper or tiles. In order to get as good a reason as possible, it is important to choose the right filler on the right occasions. There are a wide variety of variants to choose from, depending on where and where it will be spilled.
Filler is a mass that is placed in cavities and covers over joints during renovations. It can be about making a wall smooth before a repainting or tapeting, or to make joints and cracks invisible in wooden furniture. It is also common to use filler to create flat subfloor and to create cases in, for example, bathrooms. Spackel can also be used to create a structure on a wall, or to hide joints in furniture. With a good flap can be made for most surfaces. For the best possible results, however, it is important to choose the right filler.
Filler is a collective name for masses filling out cavities, cracks and joints found on surfaces. They have different characteristics, depending on where to use. Here are some common varieties of filler in the market:
Coarse pellets are used for walls and floors indoors. It should have a good filling capacity and may be used on coarse surfaces when the mass is coarse. Coarse packing can also be used for broad packing and deeper cavities.
Medium packing has finer grain than coarse packing and is often used as a all-round pallet for basic work on walls and ceilings.
Finspackel is used on walls and ceilings when the demands are high on getting a really smooth and nice surface. The fine pack is perfect for splashing of joints between gypsum boards and the like. Some variants of finpackage are completely different under the name of joint or joint.
Roller pallet is a filler that fits well in broad packing when rolled. Often, the roller pallet is medium-sized, but it can also be rough.
Wet room bag is specially designed to work in bathroom environments. Are used for walls and ceilings so that they are smooth before the surface is applied.
Floor tile is used to level the floor under a floor finish. It dries quickly and withstands higher loads than the filler for walls and ceilings. Different floor tiles are suitable for different surfaces.
Floatpack is used as a basis for flooring. It is self-leveling and creates a completely flat surface on concrete floors. In bathrooms and other wet rooms, a float compartment approved for wet rooms must be used.
Outdoor patch has been specially designed to handle outdoor surfaces. Do not use indoor packaging for these jobs. They are not able to handle that environment.
Snickerispackel is like a filler for the joinery.
Floor pellets are usually fast-cure and therefore dry much faster than wall pellets, so that they can not be completely dry when dry, without adherence, which is a prerequisite for the formation of new cracks in furniture and other wood products. in 15-30 minutes. This type of filler must usually withstand greater strain. With floor tile you can level the surface, but also build up cases when required. You should generally not lay thicker layers than about 2 cm at a time.
In addition to flooring, there is a self-leveling flap, so-called floating package. This flap is fluid and is used for example when you are getting a worn cement floor all the time. The liquid mass is poured onto the floor and then cautiously distributed with a very wide flap.
Wet room pack is a specially designed material for wet rooms. You should always use this type of filler when working in wet rooms, such as a bathroom, laundry, etc. The material, along with other wet room materials, helps keep moisture and mold away from distances.
Fragrances for carpentry should be used to make cracks and even surface on cabinet doors, furniture etc. If the wood has not been painted before, you should ground the surface before fluffing. This makes the mass better and it will also be easier to process. If you need to make a layer in a wooden surface, you can not use plain filler. The surface after normal flaking becomes white or grayish and the coating becomes ugly and clear. Instead, choose plastic wood in a suitable wood color. Smaller layings with this mass can be almost invisible.
Filler masses are sold ready mixed in a tub or in a bucket. Some flakes are fast-cure and can only be used for a short time - about 30 minutes are common. Therefore, always read the instructions carefully before opening the package or mixing the filler mass.
Filler is sold either in ready mixed or dry condition. Thoroughly mix the water with the instructions according to the instructions. Today most of the filler is bought and ready for use. It's handy and easy. What's even more important than packing comes in for packaging, are the qualities that have been spilled. A good filler should have:
• Good fillability
• Be easy to work with
• Have a consistent quality
• Easy to sand the surface of
• Attach well
• Wipe fast without cracking
Keep in mind: Each manufacturer has several different types of filler adapted to different surfaces, purposes and purposes. They can also give these different names, which do not quite match the breakdown as we did above. Read the package carefully as to what the filler should be used for and ask the store if you are unsure which fitting sort fits in the individual case.
NB! - A cheap filler can be expensive in the long run! Since fluff is generally a small cost in the context, it pays to focus on quality. Also make sure to use the right filler for the right time.
Filler is a mass that is stripped of a filler spade. Sometimes roles are also used, especially if the surface to be spilled is large. The mass usually contains fillers, solvents, binders, cores and additives.
Fillers: The most important ingredient of all of them. The finer filler, the smoother becomes the surface of the iguined area. The filler may consist of sand, powdered dolomite, limestone, chalk or kaolin. In finsackel, the filler may partly consist of aluminum silicate or plastic.
Solvent: To make the flap easy to handle, water is added.
Binders: Without binder, the sand rips apart when the flap dries.
Consistent Sensor: With a consistency sensor, the filler mass becomes easy to handle and work with.
Additives: In order to To give spackled special properties, additives may be needed in the mass. It can be a means of controlling pH, pigment, antifouling agents, preservatives and mold protection.
After finishing work, you can usually wash away filler residues from tools and tools with water. There is also ready mixed spackel that is ironed out with a roller. This filler is intended for substrates of concrete, concrete and lightweight concrete. You level to the surface using a wide flap.
Always use eye protection when sanding a fluffy surface. In case of larger grinding operations, you should also use respiratory protection. The sludge can otherwise irritate or damage eyes and respiratory tract.
There are several types of filler for wall and ceiling indoors. If you want to widen large areas, it's convenient to roll out the mass.
Select floor coverings according to the substrate and other conditions. Should you build up the fall of Ford's strong filler. Self-leveling mass sk. Flying packet is handy on worn, cast floors.
When doing wet laundry waxwork, always use wet room packages.
Use special filler for carpentry. For best results on flat surfaces, such as cupboard shutters, wide-flattened surfaces that have not been painted before.
Wood surfaces that are not covered should also be necessary. Select plastic wood in a suitable wood color and refill cracks and small damage in several layers.
There are also different types of filler for varying outdoor work. These outdoor patches can often be used for example to make sockets.