Painting the wooden facade? Here you will get valuable tips when painting a wood facade. You can also find descriptions and instructions on painting the wood façade.

Painting the Wood Facade - Tips on Painting the Facade

Painting the Wood Facade - Tips on Painting the Facade


In this article on painting a wood facade you will find detailed information and do it yourself with explanatory photographs on how to paint the wood façade.

The is an extensive work to paint the wooden facade of the house. Because it takes a lot of time, money and effort, it's important to be careful about all the preparations and all pre-work before you start painting the wooden facade. Then you have created the best conditions for the new look of the house being admired both at a distance and close range. The most important thing is that the facade has a significantly longer durability.

Whether you are painting untreated or previously painted wood, it is important that you give the color the conditions for attachment. The most important thing is a clean and dry wood. If the untreated wood has remained unprotected for a longer period of time, the surface layer has started to break down. You see this through the formation of a gray barrier on the surface. Before impregnating and foundation, brush the entire wood facade with a steel brush.

If the surface of the facade has been painted earlier, it includes cleaning with ammonia solution or target washing and then rinsing with clean water in the preliminary work. Since the painting surface becomes wet it is important that the wood gets dried properly before starting the painting work. Instead, scratch the wood facade, where necessary, while the surface is moist. It facilitates this rather time-consuming, but important part of the process.

If you are unsure whether the woodwork is dry enough, you can rent or possibly borrow a moisture ratio meter at the color handler that delivers the color. The wood should have a humidity of less than 15 percent to be a good painting base.

Wood facades that have not been maintained for a long time can have algae, rot or mold attacks. The most common places are on the shadow side, near the ground and behind dense bushes. In such cases, it is not enough to wash the wood facade with ammonia solution. These surfaces should be cleaned with a special agent that is disinfectant. When selecting color for a previously painted wood facade, it is important that you choose a color type that "tolerates" the underlying color layer. A good rule of thumb is to always paint with the same color type as the house has been painted in the past.

If you want to coat on a crushing surface, such as red paint, first brush all the loose material with a steel brush. Then you basically paint the sludge again or with an oil-alkyd primer. It is a prerequisite that the topcoat, regardless of type, will adhere to the substrate. The choice of topcoat is basically between latex paint and alkyd oil paint. Both color types provide a perfect surface protection and good results. It is the color of each color that allows you to control the selection. There is also no big difference between the price between the two.

Some of the differences between the latex and the alkyd oil are these: The surface and color of a wooden facade painted with latex paint last longer. In addition, this color type does not cite. The surface layer of an alkyd oil paint is harder but also more elastic and penetrates better into the substrate. The latex color, on the other hand, is more environmentally friendly and less flammable. To prevent the wood from being exposed to rot, it should be grounded with a penetrating base oil.

It is hard to imagine how a color changes the facade and the appearance of the house. If you want to change color, you can now get help with coloring a computer in some stores. You then print a computerized image of a house type that matches your own residence. Next, you color the façade and carpentry with different combinations. Once you've got a color scheme that matches your wishes, you'll find out what the colors are like and then just order.

If you live in a group or in a densely populated area, there may be some restrictions on the exterior color scheme of the house when painting the wood façade. Therefore, always contact the villa association and the municipality's building committee for the sake of clearing.

Wooden facades are rarely completely smooth. Because it is important for the paint to bridge the joints between the panel boards and thereby form a homogeneous surface layer, paint it with brush.

There are special so-called wide, thick and dense facade brushes. If you complete these with a pair of round anchors of suitable sizes, you can do the woodworking fine. If you have a standing panel, you can complete with a wide element brush with angled shaft, making it easier to access the woodwork's hood surfaces.

Here's how to paint a woodfade:

Tools:
Brush screws (5) Steel brush (6) Socket or screwdriver (7) Cap saw (8) Angle hook (9) Pencil (8) Pencil sharpener 10) Hammers (11) Fine brushes, such as dashes (12) Steel packing (13) Brushes (14) Moisture ratio meters, e dyl (19) Protective gloves (20) Ladders, Rejä boards, ev.

Material:
Protective Film, Masking Tape, Ammonia, Anti-Algae and Mold Cleaning, Zinc-plated wire mesh, Slippers in a pair of coats, Rust-proof paint, Acrylic sealant, Basic color for outdoor or thinning, Coating paint, latex, oil or alkyd oil paint, Wood impregnation

Woodworking for Wood Paving Painting

Underlay Desired Area Preworking Underwork Covering
New Flat or Non-Woodworking. Covering. None. Coat of special primer. Coat of latex or alkyd oil paint.
New wood-based wood. Coating. None Primer with special primer. > Coat of latex or alkyd oil paint. Previously painted with oil or alkyd oil paint.
Coating. Wash with target paint. Clean from mold and algae with special means. Scrape loosely-colored color. Create clean wood surfaces with special primer for outdoor use. Primer with diluted oil paint. Paint 2 times with oil alkyd paint. Painting 2 times with oil paint. Previously painted with latex paint.
Covering. See above. Ground clean scratched lots with special primer for outdoor use. Paint 2 times with latex paint for outdoor use. See above.
Cover paint 2 times with latex or alkyd oil paint. Prefabrication 1.Table windows, ground and adjacent plants with protective plastic and possibly masking tape. 2. Mix 1 part of ammonia to 10 parts of water or use target wash and thoroughly clean the wood facade. Use hard brush, possibly with long shaft. 3. If the facade has a mold, rotting attack, or a grave grip, the wooden facade must be scrubbed with a special means. Apply to the liquid with a brush or low pressure syringe.

4. Scrub the facade surface with a root brush. The medium is strong, so wear gloves and goggles.


5. After careful cleaning of the wood facade, rinse the surface thoroughly with water. For example, use the water hose.


6. Scrape all loose-colored paint on the wooden facade. The triangular scraper is usually the easiest to access.


Always wear protective gloves when working with ammonia. If you are going to wash the wood facade with even stronger means to get rid of algae and mold attacks, you should also protect your eyes with goggles. These preparations are strongly corrosive. Always read the operating instructions carefully before using any means such as mold. Some means should not be rinsed off the wood facade, but instead wipe with the wood.


Tip!


If you are unsure whether the wood facade has previously been painted with oil or latex paint, you can do a simple color test: Moisten a T-Liquor cloth and rub it against the wood facade. If the liquid dissolves the paint it is a latex paint. If you do not get any paint on the cloth, it is most likely an oil alkyd paint. If you want a more accurate assessment, turn to a color shop with a small piece of wood facade. Some stores are able to test and determine the color type with greater certainty.


Worth knowing

It is not uncommon for wood to get close to plants with a green hatch. This is usually an alpha trait. It can sometimes be difficult to distinguish between dirt and mold. However, mold is usually sparse while dirt is drained on the wooden facade. If you have this kind of attack on the wood façade, for example behind bushes, consider moving the bushes in conjunction with the re-painting. This allows you to extend the life of the woodwork significantly.

7. Be especially careful to scrape at joints between the panel boards on the wooden facade. This is especially true of overlapping panels, such as lid panels.

8. Steel brush then the facade surface. Then you can get rid of additional loose paint that you have missed when scrapping.

9. Feel so that the wood is not painted with a pointed object, for example a syl. Particularly sensitive places are drip edges.

10. Murket wood and ev. bad panel boards should be removed. Unscrew the panel board and tension it with a tab.


11. Cut about 20 cm above the attack. Keep the saw saw upwards at 45 ° angle and cut off the masonry board.


12. Use the board punch as a template when you saw the replacement board. Nail this and the remaining board.


13. Examine the entire wood facade so that the panel boards are stuck. Insert nail bumps.


14. Rusty nails can discolor the newly painted wooden facade. Grind and rustproof paint with a small brush.


15. Seal all cracks, slits and quarries in the wood with acrylic sealant. Let dry.


16. Release the packed portions. Also grind if the substrate has a smooth surface. Use coarse release paper.


17. Brush the surface and make sure that the wood facade is sufficiently dry to paint. Rent a moisture ratio meter.


18. New end wood should always be impregnated before foundation and cover. This prevents root attacks on the wood facade.


Paint the wood facade


1. Thoroughly measure all clean wood surfaces with an oil-based primer for outdoor use.


2. Also, measure all end wood carefully. If it is difficult to access, you can use a wide element brush that is angled.


3. To avoid a flammable surface, plan the painting. Work in approximately 1 meter wide field and paint the wood facade from top to bottom.

4. On the horizontal wood panel you work throughout the length of the house and with some panel boards at a time.


5. Be sure to work with the brush so that the paint is also part of the panel joints.


6. On the standing wood panel you will instead paint the entire height of the house and with a width of one meter at a time.


7. For example, for cover panels, it is important that the color penetrates behind the overlay panel and covers the joint.


8. When painting at windows, you protect the liner in a varied color with a wide-flap or cardboard board.


9. If the edge of the lining is to be painted in the wood phase, you should use a round brush.


10. Avoid overlap of paint. The risk is that the joints are clearly visible and the finished surface becomes flammable.


11. Even when covering, all end wood must be carefully treated with brush and paint.


12. Whether the wood façade has been painted before, you should finish it again.


If you are going to paint the wood facade on a high ladder that is tilted to the wall, this should be anchored well. One way is to knock down a pole under the steps and steal the steps in this.


You can set up a work position yourself using two double ladders and a pair of solid planks. If the house facade is high, you should rent a smaller building position instead.




Video: Painting a facade -- step by step|

Share

Comments