Change a stainless steel sink? Here you will find tips and describe how to replace an old sink for a new stainless steel sink.

Stainless sink - How to change a sink in stainless steel

Stainless sink - How to change a sink in stainless steel


A stainless steel sink may become tired and hard to keep clean, and then it's time to change it. The work is usually not complicated, but may involve some extra jobs around the counter, so the final result will be good. Examine carefully how the old sink is mounted and what workouts this results in your kitchen. If you then plan carefully before you begin, the change itself does not take so long. It is not uncommon that the wall above the sink is tiled. The tile helps to make the kitchen comfortable, but it is primarily a splash cover that is easy to keep clean.

If you have tile at the sink, this usually is over the counter of the sink, which may mean you have to take down tiled to loosen your old sink. If the wall is tiled over a larger surface, check if you can get new tiles of the same kind to complement, unless you're looking to renew and tile over the sink. The costs of changing the sink can thus be greater than you thought from the beginning. Even if it is easy to replace the old stainless steel sink, you should carefully investigate the consequences that the change may have for the kitchen as a whole. In our example, it was necessary to change both the cabinet under the sink and tiled on the wall.

Stainless sink or composite?

Work in the kitchen should be convenient. Therefore, be sure to change the height of the sink if this can increase the well-being of the sink. If you want a lower height, cut a piece of the base on the underside. Do you need to raise, instead, make a higher base. The range of washbasins is large. One can get one, two or three hoars and the bench surface can be completely smooth or with relief pattern. You can choose a sink to suit your own wishes and needs today. You can choose from a traditional stainless steel sink or perhaps a sink in composite material that is in the appropriate color for your kitchen. An alternative to the auxiliary stainless steel countertops are stainless steel drawers for woodworking or laminate discs. However, the installation and installation of stainless steel dishes differs somewhat from the type we show in this article.

All kinds of kitchen renovations stop many important everyday chores. The planning should therefore also include some of these in order for the work to be done as smoothly as possible. Also, keep in mind that the water will be shut down for a large part of the day. If you can not turn the water off in the kitchen separately, you lose the current water requirement on the dunk instead. Otherwise, it will be as good to get water in the bathroom.

The pipes under a sink

Mounting a stainless steel sink on the cabinet is simple. In principle, it is only possible to sew and glue with sizing adhesive. However, fitting cranes, pipes and sewers takes a little longer. If you live in an older house, it's important that you know all pipe dimensions already when you choose the sink and the faucets. Then you can get expert help with the connections and other accessories you may need. The connection between the drain and the sink usually follows the new sink. There is not always a crane for a sink, but you can do it yourself. This makes it easy with a drill bit equipped with metal drill bits and a screw hole puncher.

When working with pipe connections, it is also advisable to also install a water filter under your sink. With the aid of a T-pipe coupling, a portion of the cold water is passed through the filter, cleaned and then taped through a separate faucet on the sink. The advantage of the separate cranes is that you have constant access to a fresh and good water without poison, deposits etc. while you can use the second faucet for drinking water. The wear on the cleaning filter will also be less in this way.

The space in the cabinet under the sink is largely taken up of pipes, filters and hoses that can not be built. However, when you reconnect the installation, you can still make sure that the cabinet is fully utilized. The decorations that belong to the cabinet rarely use, but it is not hard to make shelves with dimensions and recesses that fit. Because you should allow the water lock to be easily accessible, you may need to attach the shelves to the brackets.

Here you need to replace a stainless steel sink:

Tools:
Two wrenches or keys (1) Bucket (2) Polygrip (3) Hammers (4) Huggjjsel (5) Drill with metal drill steel (6) Spackle (7) Jigsaw (8) Long water pass (9) Tumstock (10) Pen (11) Angle hook (12) Ruler (13) Screwdriver or Screwdrivers (14) Screwdrivers (15) Screwdrivers (15) Screwdrivers (16) Toothed Spackles (17) Screwdrivers or Arches (18)

Material:
Stainless steel sink with drain outlet, Kitchen mixer, Kitchen cabinet, Plasterboard, Plastic foil, Sandpin, Gypsum screw, Clamp clutches, Dyckert, Fogmassage, Softfog, Trasa, Krita.

Planning

1. Examine how your old stainless steel sink is mounted and then assess the extent of the renovation.
2. Take all measurements and see a new stainless steel sink or choose another material on the sink.
3. Also make sure that you get all the connections required and that they have the correct dimension.
4. If you are going to complete tiles or other wallcoverings, find out if the material is in the store.
5. Make sure food and water are readily available, as the kitchen is more or less out of order.
During work.

Worth knowing

If you live in an older house, without separate shut-off taps, you can easily supplement it in connection with the change of your sink. Measure the dimensions of the old pipes with sliding dimensions to get the correct pipe fittings for installation. If you have cast iron drainage pipes, measure the inside dimensions of the muffler. You may need to complete the new drain pipe with a reduction kit and possible sealing compound. You should always contact an authorized plumbing company for safe water installation when you are renovating the kitchen.

Remove the old sink


1.Place the water in the kitchen either with the shut-down cranes located under the sink or with the main crane.


2.Use two keys and remove the connection to hot and cold water, as well as the dishwasher.


3.Place a bucket under the drain and have a cloth in standby. Then loosen the connections to the sink.


4.To remove the entire drain pipe between the sink and the drain. It comes with new sewer pipes to the new bench.


5. Many times, it is also necessary to remove the splash guard above the sink to get rid of it.


6. Here you can see how the bin clamp is stuck.


7.To remove the sink and the cabinet and cut off the part of the plasterboard as tiled.

Prepare for your new sink.


1.Remove cardings between the transverse lines and attach the gypsum plates left in them.


2.With the wall behind the sink is an outside wall, this should have a vapor barrier. Therefore, dress the insulation with plastic wrap.


3.Met and cut into new plasterboards to the wall surfaces where you are going to tile. Use the angle hook and sharp knife.


4.Place the plates with a plaster screw. If there are many screws, the work of an electric screwdriver is facilitated.


5.Pack over screw heads and joints. When the dirt has dried, sand the surface evenly with the drip and dirt.

Install a new sink


1.The wardrobe should be "figursys". Mark sawmarks after the drawers, then make the recesses with jigsaw.


2.Place the underside in place and check with water pass before attaching. Try the new sink.


3.Check - preferably with a long water pass that the bench is in full swing. Make any fine adjustments.

Mount the mixer


1. In most cases, a kitchen mixer should be placed between the sinkers. Do the measurement with thumbs.


2.Remove the mat to the inner edge of the sink and mark with a pen. Keep the protective plastic on the bench.


3.Prink the marking with drill and metal drill with the dimension larger than the hole punching screw.


4.Turn the hole for the mixer with the screwhole puncher. Turn the hole puncher with a wrench.


5.Place the new kitchen mixer in place in the recess and attach it to the underside of the sink.


6.Because the sink is not yet mounted, you can place it on the top to access lighter.


7.The countertop must be attached to the underside with a sizing adhesive. Push out a string of glue on the cabinet's abutment surfaces.


8.The strip must not get too close to the outside of the cabinet's leading edge. Add the sink, load and allow to dry.

Pipe connections


1. The pipes from the kitchen mixer must be cut to connect to the hot and cold water pipes. Use a pipe cutter.


2.The cold water is here connected with a T-connection for a pipe to a purge filter. Drag the wrenches with a wrench.


3.The new sewage pipes should first be plugged under the sink. Tighten the connections properly.


4. Connect the drain line to the drain.


5.Open the water again and check that all pipes are completely sealed.

Attach the sink


1.Low the protective plastic to be left and drill with a small metal drill in the bench clamp against the wall.


2.Set the holes at even intervals throughout the entire list.

Place a new tile above the sink.


1.Place a masonite bit against the sink, hold the plate, and hold the top of the top of the sink.


2.Print out attachment with a toothed filler and put the tile. Vertical markings on the tile facilitate.


3. When the tile sits, remove the cross and join as usual. Remove the masonite and soften the bench.

Tip!

In addition to traditional kitchen mixers, you can also choose a kitchen mixer with removable shower head with a soft hose. It works partly as a normal faucet, partly in the same way as a shower. Because you can remove the ejector from the bracket, you are not as bound at the mixer's position on the sink. Just make sure that the long hose runs freely over the sink without gripping pipes or fittings. Use transparent and waterproof sealant in the joint between the sink and other bench surfaces. Then water and dirt can not creep into the gap and form bacterial herbs. The kitchen is also easier to keep clean. Because washbasins are subjected to severe wear, you should also take the habit of regularly reviewing the seal.

Important!

New material regulations, rules, recommendations, and working methods are constantly on hand. Therefore, always check the current rules with the current professional organization / professional before starting.



Video: How-to Install a Stainless Steel Drop-In Sink | Moen Installation Video|

Share

Comments