This article provides detailed information and valuable tips on what to consider when using pipe buckles and pipes For plumbing jobs.
A home cutter currently has access to plastic pipes and some other equivalent materials, which are so easy-to-handle that you only need a few tools and rarely any special tools. You can bend and bend the pipes by hand, possibly in simple templates. However, when working with such hard pipe materials as steel, iron and copper and must bend or bend them to get a good and well-functioning assembly, completely others need to. Among other things, pipes and pipes are needed, depending on the material and dimension.
It is far from all pipe work that homeowners can or may do themselves. However, it does not mean that pipe work, even in the case of hard pipes, is banned for the home cutter. An absolute prerequisite for being able to handle maintenance and some repairs is that you have good working equipment. Wrenches and simple Polygrip type pipes are equipment that belongs to a fairly normal tooling device. Particularly when it comes to smoother pipe dimensions, you can do a lot with these tools.
Many of them can also be used for work that is not directly related to pipes. This is especially true of polygrams, sometimes also called motor and multiflex extenders. However, when it comes to big pipes, pipe screws and tube buckets, you get into a completely different situation. The cost of such equipment is so high that it is for strong reasons to be provided for individual use. As a rule, these reasons are not available, mostly because the tools are only used on occasional occasions. It is then more logical to let them become common property in, for example, a villa or quarrel, just as you can agree on jointly-owned motorhacks, power-driven lawn mowers, laundry service, community rooms, etc.
It should also be noted that heavier pipe equipment can often rented by the plumbing company that supplies the pipe material. Often, the road is both the easiest and the cheapest. A logical question is if you need special equipment for pipe work at all? The answer is yes. This is due to the fact that during pipe bending, sharp angles must be avoided on the inside of the pipe. At every attempt to bend a pipe without special tools and without the help of, for example, sand, the tube will be stretched on the outside while compressed inside.
There is a large and dimension range of tools used for machining
of pipes. The following tools are just a few examples:
The pipe screw (1) has hardened steel jaws. Among a number of pipe bockers, the (2) rotating back roller is particularly gentle, suitable for heat insulating copper pipes. The pipe bucket also has plastic insulating steel pipe handles. (3) is intended for plastic insulated copper tubes and very useful in confined spaces. At the beginning of the bending the handles are at approximately 100 ° angle. The rating is 0 90 °. The bucket (4) is intended for both thinner and thicker copper pipes, thin-walled steel pipes, plastic coated copper and steel pipes, stainless steel pipes and aluminum pipes. It bends with small radii from 0 to 180 °. It is intended to be stuck in a screwdriver. The bucket (5) is made of fiberglass reinforced plastic and is intended for annealed copper pipe, aluminum pipe and other soft pipes. It can handle four pipe dimensions.
Tubes are also available in many designs and sizes. (6) has knurled jaws and is intended for max 1/2 inch pipe diameter, (7) for a full 3 inch diameter. At this the jaws are rounded in the bottom to increase the breaking strength. The piping rod (8) is made of chrome-plated steel and fitted with quick adjustment and clamping protection. It is also self-locking, which means it locks automatically when it is clamped around an object. The tongs (9) have a tension strap of nylon and are primarily intended for polished or chromed tubes. It also comes with a special tube for plastic pipes. The chain rod (10) is particularly suitable for use in narrow corners. For many simpler pipe work, the pliers called multifixes (11 13) are very useful.
Larger pipe bending equipment is often hydraulic and is not shown here. Tubes, which are the plumbing's most commonly used bending tools, can sometimes be hired in plumbing stores.
Even pipes may need to heat up before bending them, but not as high as copper pipes. It is not quite easy to find the right temperature, but it is better that the heat is too low than too high. Use a hot air gun, for example, to fix it in a screwdriver and then keep the tube moving over the hot air jet. If you have no hot air gun, a regular hairdryer is a good replacement.
Keep in mind that you must have the building board's approval for draining pipes connected to the municipal water and sewers. On the other hand, you can maintain, clean and replace gaskets for continuous operation. In each case, coarse copper pipes must be sanded before bending. Otherwise the tube will fold. "Stir" one pipe end with, for example, a cork and fill the pipe with fine and absolutely dry sand. If the sand is damp it expands when the tube is heated. Then put a cork even in the other tube end. Heat the tube and bend it over for example a rounded edge or a screwdriver. Wait to remove the plugs and sand until the metal has cooled.